Evans Pre-Dip Teat Disinfectant 25L
Evans Vanodine Pre-Dip is a ready-to-use iodophor teat disinfectant for preparing cows' teats before milking. It is intended for manual dipping or application with an electronic sprayer, followed by thorough wiping and drying before milking begins.
The product is supplied undiluted, avoiding the measurement and mixing needed with a concentrate. This listing supplies the 25-litre container, manufacturer code R029KEV. A dosing pump is recommended by the manufacturer for filling application equipment, with clean cups or suitable spraying equipment used throughout the routine.
Pre-Dip has documented activity against bacteria and yeast under specified laboratory test conditions. Its practical manual-use instructions require a minimum contact time of 60 seconds. That application time remains essential even though the manufacturer also reports shorter times for particular laboratory suspension tests.
Use Pre-Dip within your planned pre-milking teat care routine and manage equipment cleaning separately with the dairy hygiene range. The related product information, safety sheet and microbiological profile support consistent preparation, full teat coverage and correct handling of this formulation.
Key Features & Benefits
- Pre-milking preparation: designed for cleaning and disinfecting cows' teats before milking.
- Ready to use: apply undiluted, with no concentrate measurement or mixing.
- Two application methods: manual dipping or manual spraying using an electronic sprayer.
- Clear manual procedure: cover the full teat for at least 60 seconds, then wipe and dry thoroughly.
- Documented test evidence: EN 1656 bacterial and EN 1657 yeast results are detailed in the manufacturer profile.
- 25L container: supplies the R029-KEV variant for routine dairy teat preparation.
Directions for Use
Prepare the teats and equipment
Read the current label and related documents. Ensure the udder and teats are clean and dry before application. Use Pre-Dip undiluted; a dosing pump is recommended when filling application equipment. Wear suitable chemical-resistant protective gloves as directed by the current safety sheet.
Apply by manual dipping
Fill the teat dip cup two thirds full with product. Dip each cow's teats before milking, immersing their full length. Keep the full teat covered for a minimum of 60 seconds, then wipe and dry thoroughly with a single-use paper towel.
Apply with an electronic sprayer
Before milking, spray the entire surface of every teat with Pre-Dip. Ensure complete coverage and leave the product on for at least 60 seconds. Then wipe and dry the teats thoroughly using a single-use paper towel before milking.
Maintain the equipment and store correctly
Top up with fresh solution as required and empty and wash out cups with water after use. Store the original container tightly closed in a cool, well-ventilated place away from oxidising materials. Follow local disposal requirements and avoid release to an on-site wastewater treatment plant, as specified in the product information.
Product Specifications
| Specification |
Details |
| Manufacturer |
Evans Vanodine |
| Product |
Pre-Dip |
| Listed pack |
25 litres |
| Manufacturer pack code |
R029KEV |
| Listed variant SKU |
R029-KEV |
| Formulation |
Ready-to-use liquid iodophor-based teat disinfectant |
| Milking stage |
Pre-milking |
| Manual application |
Dipping or spraying using an electronic sprayer |
| Minimum manual contact time |
60 seconds, followed by thorough wiping and drying |
| Appearance and odour |
Dark brown liquid with a faint iodine odour |
| Undiluted pH |
4.0 |
| Manufacturer test evidence |
EN 1656 bacteria, EN 1657 yeast and modified EN 16437 surface testing; see profile |
FAQs
When should Pre-Dip be used?
Pre-Dip is intended for teat preparation before milking. The manufacturer specifies application before each milking, with full teat coverage and the required contact time. Complete the wiping and drying steps before milking begins.
Does Pre-Dip need dilution?
No. It is supplied ready to use and should be applied undiluted. The manufacturer recommends a dosing pump when filling application equipment. Keep cups and sprayers clean and replenish with fresh product as required.
Is the manual application time 15 or 60 seconds?
Use at least 60 seconds for the manual dipping or electronic-sprayer procedure. The 15-second figure refers to EN 1656 laboratory bacterial suspension testing at the stated conditions. It does not replace the 60-second practical application instruction.
What should happen after the contact time?
Wipe and dry the teats thoroughly using a single-use paper towel before milking. This follows both manual dipping and electronic-sprayer application. Full coverage, the minimum contact time and the final preparation steps all form part of the manufacturer's procedure.
What testing is included in the profile?
The profile lists EN 1656 bacterial tests at 15 seconds, EN 1657 yeast tests at 30 seconds and modified EN 16437 surface tests at one minute, all under the specified pre-milking conditions at 30°C. Read the full tables for organisms and conditions and follow the application instructions for use.
What pack and handling information are provided?
This listing supplies the 25-litre R029-KEV variant. The Related Documents section contains the safety data sheet, product information sheet and microbiological profile. The current safety sheet specifies protective gloves; consult the documents and container label for full storage, handling and disposal requirements.
